External gear pump AZPB
The displacement of the PA-AZPB series of POOCCA external gear pumps ranges from 1cc to 7cc. Slide bearings for heavy duty applications, Long service life thru reinforced design of shafts and gray cast iron cover.
Name |
PA-AZPB Series Hydraulic gear pump |
Series |
Series B |
Sizes |
1 2 2.5 3.1 4 4.5 5 6.3 7.1 |
Nominal Pressure |
230 bar |
Maximum Pressure |
250 bar |
Operation Mode |
External Gear Pumps |
Displacement |
V |
cm3/rev |
1 |
2 |
2.5 |
3.15 |
4 |
4.5 |
5 |
6.3 |
7.1 |
Suction pressure |
pe |
bar |
0.7...3 (absolute) |
||||||||
max. continuous pressure |
p1 |
250 |
250 |
250 |
250 |
250 |
250 |
250 |
225 |
200 |
|
max. intermittent pressure |
p2 |
280 |
280 |
280 |
280 |
280 |
280 |
280 |
255 |
230 |
|
max. peak pressure |
p3 |
300 |
300 |
300 |
300 |
300 |
300 |
300 |
275 |
250 |
|
min. rotational speed |
rpm |
750 |
750 |
750 |
750 |
750 |
750 |
750 |
750 |
750 |
|
max. rotational speed at |
p2 |
6,000 |
5,000 |
5,000 |
4,000 |
4,000 |
4,000 |
4,000 |
3,500 |
3,500 |
Multiple gear pumps
Gear pumps are suitable for multiple setups,whereby the drive shaft for the 1st pump is extended to a second and even a 3rd pump. A coupling is fitted between each pair of pumps.
In most cases each pump is isolated from its neighbor, i.e. the suction ports are separate from one another. A common suction port is also possible as an option.
Caution: Basically, the specifications for the single pumps apply, but with certain restrictions:Max. speed: This is determined by the highest rated pump speed in use.
Pressures: These are restricted by the strength of the drive shaft, the through drives and the drivers. Appropriate data is given in the dimensional drawings.
-Nominal pressure 280bar;
-Using sliding bearings, suitable for heavy-duty applications;
-The drive shaft meets ISO or SAE requirements;
-Can realize the combination of multiple pumps;
-Pipeline oil port: use connecting flange or internal thread;
-Realize continuous high quality through mass production;
-A variety of configuration variants are available.
A gear pump is also called a positive displacement device, which is like a piston in a cylinder. When one tooth enters the fluid space of another tooth, the liquid is mechanically squeezed out. Since the liquid cannot be compressed, the liquid and the teeth cannot occupy a unified space in the immediate time. In this way, the liquid is removed. Due to the continuous meshing of the teeth, this phenomenon is continuously produced, and thus a continuous removal amount is provided at the pump outlet. The displacement amount is the same for each revolution of the pump. With the uninterrupted rotation of the drive shaft, the pump continuously expels fluid. The flow rate of the pump is directly related to the speed of the pump.
There is a small amount of fluid loss in the pump, which makes the operation of the pump impossible to reach*. Because these fluids are used to lubricate the bearings and both sides of the gears, and the pump body is never common without gaps, it is not possible. It is not enough to expel fluid from the outlet, so a small amount of fluid loss is certain. However, the pump can still run well, and for most extruded materials, it can still reach 93% to 98% compliance.
For fluids whose viscosity or density changes in the process, this pump will not be affected too much. If there is a damper, like a strainer or a restrictor on the side of the discharge port, the pump will push the fluid through them. If the damper changes in the event, that is, if the filter becomes dirty, clogged, or the back pressure of the limiter rises, the pump will still maintain a constant flow rate until it reaches the machine limit of the weakest part of the device. (Usually equipped with a torque limiter).
1、Self-produced and self-sold, affordable, and raw materials can be traced.
2、After-sales guarantee, convenient maintenance.
3、Fast delivery, can be produced after placing an order after payment
4、Customizable styles, OEM manufacturers, can print your company's LOGO.
5、MQQ:1
6、Support sample free service. The sample amount can be refunded in the formal order.
7、Professional technical team, 15 years of hydraulic experience. Match the products you need most.
8、12 months warranty
9、Quality inspection and testing before shipment
10、Shipment provides pictures and packaging pictures for confirmation
FAQ1、Questions: Can I sell the products with your brand online/offline?
Answer: Yes, we allow you to sell the products with our brand online/offline.
2、Questions:How about the goods delivery?Answer: By sea, by trian, DHL, UPS, FedEx, EMS,TNT and so on. It depends on your demand.
3、Questions: Can you provide products that meet CE requirements?
Answer: Yes, our all product have CE certification.
4、Questions: I want a model that is different from others. Can you design it for me?
Answer: Yes, we can design a unique model based on your ideas.
5、Questions: The product is too expensive, can you make it cheaper for me?
Answer: Yes, we can design and produce products at different prices according to your needs.
http://www.poocca.com/